HYDRAULIC FRACTURING ANALYSIS OF LOW PERMEABILTY, HEAVY OIL RESERVOIR TELISA FORMATION, BENTAYAN FIELD
Abstract
There is no proven economic oil production yet from Bentayan’s part of Telisa Layer. However, open hole log from some wells in Bentayan field indicates hydrocarbon presence in TELISA in Bentayan field. GGR study also indicated low value in permeability of Telisa in Bentayan field. Production test in BN-62 indicates oil presence from Telisa with very low influx. To prove the hydrocarbon prospect of Telisa in Bentayan field, operator planned to develop Telisa in BN-62 and BN-21 by conducting hydraulic fracturing using approximately 80,000 lbs of proppant.
Early screen out happened when fracturing both wells. After the job, these two wells could not prove economical hydrocarbon production from Telisa. Both wells only have AOFP of 3 BFPD with lack of hydrocarbon indication.
Evaluation indicated that the cause this failure on the fracturing job may be caused by smaller value of flow efficiency than it was predicted due to the large permeability zones and formation of multiple fractures that caused pad volume and the slurry pumping flow rate to be less to create the expected fracture geometry. Based on rock property map, BN-95 is suggested to be a candidate to prove the prospect of economical hydrocarbon content in from Telisa.
Keywords: well stimulation, hydraulic fracturing, low permeability reservoir, Telisa
Full Text:
PDFReferences
Al-Dossary, M., Hamid, O. dan Elkatatny, S., (2019), Effect of Pore Pressure Depletion on Wellbore Stability and Hydraulic Fracturing in Sandstone Reservoir, Paper IPTC 19097-MS, International Petroleum Technology Conference, Beijing, China, 26 – 28 Maret.
Al-Othman, M.R., Buhamad, A.A., Al-Houti, N.B., Ashkanani, M.S., Al-Mehanna, H.S., Al-Haddad, M.N., Al-Dhafiri, A.A., Al-Harbi, S.M., Al-Ibrahim, A.A., Al-Zuwayed, A.M., Ahmed, A.M. and Al-Dousari, M.A., (2016), Unlocking the Potential of Marginal Reservoirs in Kuwait Through the Application of Optimized Hydraulic Fracturing Technologies, Paper SPE 181887, SPE Annual Technical Conference and Exhibition, Dubai, UAE, 26-28 September.
Almond, S.W., Bland, W.E. dan Ripley, H.E., (1984), The Effect of Break Mechanisms on Gelling Agent Residue and Flow Impairment in 20/40 Mesh Sand, Paper CIM 84-35-30, The 35th Annual Technical Meeting of Petroleum Society of CIM and Canadian Association of Drilling Engineers, Calgary, Alberta, Canada, 10–13 Juni, 1984.
Almond, S.W. dan Garvin, T.R., (1984), High Efficiency Fracturing Fluids for Low Temperature Reservoirs, Proceeding 31st Annual Southwestern Petroleum Short Course, Lubbock, Texas, USA, 76–88.
Azhari, M., Prakoso, N.F., Ningrum, D., Soetikno, L. dan Makmun, A., (2017), Unlocking Depleted and Low-Modulus Telisa Sandstone Reservoir with Pillar Fracturing Technique: Well Performace Improvement Comparison with Conventional Fracturing, Paper SPE 186199, SPE/IATMI Asia Pasific Oil and Gas Conference and Exhibition, Jakarta, Indonesia, 17-19 Oktober.
Carico, R.D. dan Bagshaw, F.R., (1978), Description and Use of Polymers Used in Drilling, Workovers, and Completions, Paper SPE 7747, SPE Production Technology Symposium, Hobbs, New Mexico, USA, 30–31 Oktober.
Carter, R.D., (1957), Derivation of the General Equation for Estimating the Extent of the Fractured Area, Appendix I Optimum Fluid Characteristics for Fracture Extension. Drilling and Production Practice, G. C. Howard and C. R. Fast. American Petroleum Institute. New York, USA, 261 – 269.
Cinco-Ley, H., Samaniego-V., F. dan Dominguez, N., (1978), Transient Pressure Behavior for a Well with a Finite-Conductivity Vertical Fracture, Paper SPE 6014, SPE Annual Technical Conference and Exhibition, New Orleans, Louisiana, USA, 3–6 Oktober, 1976), SPE Journal (Agustus 1978) 18, 253–264.
Cipolla, C.L. dan Wright, C.A., (2000), State of the Art in Hydraulic Fracture Diagnostics, Paper SPE 64434, 2000 SPE Asia Pacific Oil and Gas Conference, Brisbane, Australia, 16–18 Oktober.
Cleary, M.P., (1993), Field Implementation of Proppant Slugs to Avoid Premature Screenout of Hydraulic Fractures with Adequate Proppant Concentration, Paper SPE 25892, 1993 SPE Rocky Mountain Regional/Low Permeability Reservoirs Symposium, Denver, 12–14 April.
Clifton, R.J., (1989), Three-Dimensional Fracture-Propagation Models. Recent Advance in Hydraulic Fracturing, J.L. Gridley et al (eds.), Chapter 5, 95, Monograph Series, SPE, Richardson, Texas.
De Coster, G. L., (1974), The Geology of the central and South Sumatera, Indonesia Petroleum Association 3rd Annual Convention, pp 77-110.
Economides, M.J., Nolte, K.G., (2000), Reservoir Stimulation: Third Edition, John Wiley and Sons Ltd. West Sussex, England.
Ezekwe, N., (2011), Petroleum Reservoir Engineering Practice, Pearson Education Inc., Boston, Prentice Hall, USA, 258-264.
Gruesbeck, C dan Collins, R.E., (1978), Particle Transport through Perforations, Paper SPE 7006, SPE Symposium on Formation Damage Control, Lafayette, Lousiana, USA, 15-16 Februari.
Harrington, L.J, Whitsitt, N.F., dan Hannah, R.R., (1973), Prediction of the Location and Movement of Fluid Interfaces in the Fracture, Southwestern Petroleum Short Course, Texas Tech University, Lubbock, Texas, USA.
Hamzah, K., Prakoso, N.F., Yudhanto, G., Soetikno, L., Marbun, R.D., Vitali, R., Makmun, A. dan Anis, A.S.L., (2018), Paper SPE 191990, SPE Asia Pasific Oil and Gas Conference and Exhibition, Brisbane, Australia, 23-25 Oktober.
Harris, P.C., (1985), Dynamic Fluid-Loss Characteristics of Nitrogen Foam Fracturing Fluids, Journal of Petroleum Technology (Oktober 1985) 18, No. 10, 1847–1852.
Howard, G.C. dan Fast, C.R., (1970), Hydraulic Fracturing, Monograph Series, Richardson, Texas, USA, Society of Petroleum Engineers 2.
Hubbart, M.K. dan Willis, D.G., (1957), Mechanics of Hydraulic Fracturing, Trans. AIME 210, 153.
Hunter, J. dan Walker, R.N. Jr., (1991), Clean Frac Fluids Improve Load Recovery, Tight-Gas Production, World Oil (Oktober 1991) 212, No. 10, 76–78.
Kartiyasa, F.A., Sitaresmi, R., Wahyuni, M.G.S., Oetomo, H.K. dan Suandana I.W., (2019), Paper SPE 196343, SPE/IATMI Asia Pacific Oil and Gas Conference and Exhibition, Bali, Indonesia, 29-31 Oktober.
Ketineni, S.P., Tan, Y., Hoffman, K.L., Jones, M. and Ghoraishy, M., (2019), Unlocking Additional Barrels from a Mature Conventional Oil Field through Unconventional Technologies: A Case Study on Rangely Oil Field, Colorado, Paper SPE 196033, SPE Annual Technical Conference and Exhibition, Calgary, Alberta, Canada, 30 September – 2 Oktober.
Lake, L.W., Clegg, J.D., (2007), Petroleum Engineering Handbook Volume 4, Production Operations Engineering, Chapter 8: Hydraulic Fracturing, Society of Petroleum Engineers, Texas, USA.
Lipton, D. dan Burnett, D.B., (1976), Comparisons of Polymers Used in Workover and Completion Fluids, Paper SPE 5872, The Improved Oil Recovery Symposium, Tulsa, Oklahoma, USA, 22–24 Maret.
Manaf, N.A. dan N. Mujahidin., (1993), Evaluasi migrasi hidrokarbon di sub cekungan Jambi berdasar pemelajaran biomarker dan sejarah tektoniknya, Proceedings Indonesian Association of Geologist, 23rd Annual Convention, 736-758.
Martocchia, F., Itoua, R.V., Farina L., Baretti, S. dan Martini, L., (2014), Hydraulic Fracturing Across Large Existing Perforated Interval Unlocks Reserves on Tight Sandstone Reservoir: Successful Workover Experience, Onshore Congo, Paper IPTC 17994, International Petroleum Technology Conference, Kuala Lumpur, Malaysia, 10-12 Desember.
Marshall, H. E., (2000), Technology Management Handbook, Boca Raton: CRC Press LLC.
McClain, C., (1963), Fluid Flow in Pipes, New York, USA, The Industrial Press, 117–128.
McGuire, W.J. dan Sikora, V.T., (1960), The Effect of Vertical Fractures on Well Productivity, Paper SPE 1618-G, Journal of Petroleum Technology (Oktober 1960) 12, 72–74.
Nolte, K.G., (1979), Determination of Fracture Parameters from Fracturing Pressure Decline, Paper SPE 8341, SPE Annual Technical Conference and Exhibition, Las Vegas, Nevada, USA, 23–26 September.
Nolte, K.G., (1986), Determination of Proppant and Fluid Schedules from Fracturing Pressure Decline, Paper SPE 13278, SPE Production Engineering 1, No.4, 255 – 265.
Nolte, K.G. dan Smith, M.B., (1979), Interpretation of Fracturing Pressures, Paper SPE 8297, The 54th Annual Fall Technical Conference and Exhibition of Society of Petroleum Engineers of Aime, Las Vegas, Nevada, USA, 23-26 September.
Poerwanto, J.H., Sugembong, C.F., Bagzis, J.M., Martinez, A.D., (1995), Application of Hydraulic Fracturing Technologies to the Shallow Telisa Formation, Paper SPE 29282, The 1995 SPE Asia Pacific Oil and Gas Conference and Exhibition, Kuala Lumpur, Malaysia, 20-22 Maret.
Prats, M., (1961), Effect of Vertical Fractures on Reservoir Behavior-Incompressible Fluid Case, paper SPE 1575-G, SPE Journal (Juni 1961) 1, No. 1, 105–118.
Pulsinelli, R.J. dan Brannon, H.D., (1992), Breaker Concentrations Required to Improve the Permeability of Proppant Packs Damaged by Concentrated Linear and Borate-Crosslinked Fracturing Fluids, Paper SPE 21583, SPE Production Engineering (November 1992) 7, No. 4, 338–342.
Rachmanto, R., Pasaribu, H., Widjanarko, A. dan Halinda, D., (2019), Low Pore Pressure Hydraulic Fracturing Breakthrough inSanga-Sanga: Simple Methods in Performing Hydraulic Fracturing in LowPore Pressure Reservoir, Paper SPE 196291-MS, SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibiton, Bali, Indonesia, 29 – 31 Oktober.
Ramones, M., Gutierrez, L., Moran, M., (2015), Unlocking a Mature Field Reservoir Potential Through Optimized Fit-for-Purpose Hydraulic Fracturing, Paper SPE 177219, SPE Latin American and Caribbean Petroleum Engineering Conference, Quito, Ecuador, 18-20 November.
Reidenbach, V.G., Harris, P.C., Lee, Y.N. dan Lord, D.L., (1986), Rheological Study of Foam Fracturing Fluids Using Nitrogen and Carbon Dioxide, Paper SPE 12026, SPE Production Engineering (Januari 1986) 1, No. 1, 31–41.
Roodhart, L., Kulper, T.O.H. dan Davies, D.R., (1986), Proppant Pack and Formation Impairment During Gas-Well Hydraulic Fracturing, Paper SPE 15629, SPE Annual Technical Conference and Exhibition, New Orleans, Louisiana, USA, 5–8 Oktober.
Samuel, M., Card, R.J., Nelson, E.B., Brown, J.E., Vinod, P.S., Temple, H.L., Qu, Q. dan Fu, D.K., (1997), Polymer-Free Fluid for Hydraulic Fracturing, Paper SPE 38622, SPE Annual Technical Conference and Exhibition, San Antonio, Texas, USA, 5–8 Oktober.
Settari, A., (1985), A New General Model of Fluid Loss in Hydraulic Fracturing, Paper SPE 11625, SPE Journal (Agustus 1985) 25, No. 4, 491–501.
Simonson, E.R., Abou-Sayed, A.S. dan Clifton, R.J., (1978), Containment of Massive Hydraulic Fractures, paper SPE 6089, SPE Journal (Februari, 1978) 18, No. 1, 27–32.
Stewart, B.R., Mullen, M.E., Howard, W.J. dan Norman, W.D., (1995), Use of a Solids-Free Viscous Carrying Fluid in Fracturing Applications: An Economic and Productivity Comparison in Shallow Completions, Paper SPE 30114, SPE European Formation Damage Conference, The Hague, Netherlands, 15–16 Mei.
Tapponnier, P., G. Peltzer dan R. Armijo., (1986), On the mechanics of the collision between India and Asia, in Collision Tectonics, edited by Coward, M. P., dan A. C. Ries, Geological Society Special Publication, 19, Geological Society, London, pp. 115-157.
Ward, V.L., (1984), Nitrogen and Carbon Dioxide in the Oil Field: Stimulation and Completion Applications, Paper SPE 12594, SPE Permian Basin Oil & Gas Recovery Conference, Midland, Texas, USA, 8–9 Maret.
Warpinski, N.R., (1983), Investigation on the Accuracy and Reliability of In Situ Stress Measurements Using Hydraulic Fracturing in Perforated Cased Holes, Rock Mechanics: Theory-Experiment-Practice, Proceedings of the 24th U.S. Symposium on Rock Mechanics (Juni 1983), 773–776.
Warpinski, N.R., (1996), Hydraulic Fracture Diagnostics, Journal of Petroleum Technology 48(10), Oktober 1996, 907 – 910.
Whistler, R.L., (1959), Industrial Gums, New York, USA, Academic Press.
Williams, B.B., Gidley, J.L., dan Schechter, R.S., (1979), Acidizing Fundamentals, Monograph Series, SPE, Richardson, Texas.
McKenzie, H., Boughton, M., Hayes, L., & Forsyth, S. (2008). Explaining the complexities and value of nursing practice and knowledge. In I. Morley & M. Crouch (Eds.), Knowledge as value: Illumination through critical prisms (pp. 209-224). Amsterdam, Netherlands: Rodopi.
DOI: https://doi.org/10.31315/jpgt.v3i2.7197
This work is licensed under a Creative Commons Attribution 4.0 International License.
Slot gacor maxwin