Simulation of A Solar Drier for Iroko Wood (Chlorophora Excelsa) in A Tropical Environment

Fesa Putra Kristianto, Mercusuar Kemall Gibran Salim

Abstract


In a previous study conducted by Simo Tagne to designing a solar dryer based on mathematical equations for iroko wood in Cameroon, Africa. However, there is no complete simulation of the drying process on the tool, resulting in the lack of detailed elaboration of the iroko wood drying process. The purpose of this study is to simulate in detail the drying process on the tool using an ANSYS simulation. The model used in this simulation still uses the same mathematical model that has been studied before. This research begins by setting up the ANSYS application with the previous mathematical model, environmental conditions, and tool specifications. Furthermore, simulations are carried out using the ANSYS application with measurements of pressure, temperature, velocity and mass transfer. From this simulation obtained results for the distribution of pressure, temperature, velocity, and mass transfer. From all these distributions, it is sufficient to describe the drying process of the tool according to the mathematical model that has been studied previously.

Keywords


Permodelan Matematis; Pengering Tenga Surya; ANSYS

References


Abderrahman, M., Abdelaziz, B., & Abdelkader, O. (2021). CFD modeling of an even-span greenhouse dryer under natural and forced convection modes. Journal of Physics: Conference Series, 2022(1).

Amjad, W., Munir, A., Esper, A., & Hensel, O. (2015). Spatial homogeneity of drying in a batch type food dryer with diagonal air flow design. Journal of Food Engineering, 144, 148–155.

Aukah, J., & Muvengei, M. (2015). Simulation of Drying Uniformity inside Hybrid Solar Biomass Dryer using ANSYS CFX. … of Sustainable Research …, 336–344.

Ayangma, F., NKENG, E. G., BONOMA, B. D., & Nganhou, J. (2008). Evaluation du potentiel en é nergie solaire au Cameroun: cas du nord Cameroun. African Journal of Science and Technology, 9(2), 32â.

Bekkioui, N., Hakam, A., Zoulalian, A., Sesbou, A., & Kortbi, M. El. (2011). Solar drying of pine lumber: Verification of a mathematical model. Maderas: Ciencia y Tecnologia, 13(1), 29–40.

David, A., & Ngwa, N. R. (2013). Global solar radiation of some regions of cameroon using the linear angstrom and non-linear polynomial relations (part I) model development. International Journal of Renewable Energy Research, 3(4), 984–992.

Jading, A., Bintoro, N., Sutiarso, L., & Wahyu Karyadi, J. N. (2018). Temperature and Air Velocity Simulation on Sago Starch Pneumatic Conveying Recirculated Dryer Using Ansys Fluent. Agritech, 38(1), 88.

Kačíková, D., Kubovský, I., Ulbriková, N., & Kačík, F. (2020). The impact of thermal treatment on structural changes of Teak and iroko wood lignins. Applied Sciences (Switzerland), 10(14).

Kemajou, A., Mba, L., & Pako-Mbou, G. (2012). Energy efficiency in air-conditioned buildings of the tropical humid climate. IJRRAS, 11(2), 235–240.

Lealea, T., & Tchinda, R. (2013). Estimation of diffuse solar radiation in the South of Cameroon. Journal of Energy Technologies and Policy, 3(6), 32–42.

Nematchoua. (2014). Study of Dioxide Carbon Concentration and Indoor Air Quality in Some Buildings in the Equatorial Region of Cameroon (Yaounde). Iranian Journal Of Health Sciences, 2(1), 1–15.

Njomo, D., & Wald, L. (2007). Solar irradiation retrieval in Cameroon from Meteosat satellite imagery using the Heliosat-2 method. ISESCO Science and Technology Vision, 2(1), 19–24.

Setiawan, A. B. (2021). Analisa Kebutuhan Energi Pada Alat Pengering Rotating Parts Of Tray Dengan Menggunakan Software Ansys Fluent 2019. Universitas Gadjah Mada.

Simo-Tagne, M., Zoulalian, A., Remond, R., Rogaume, Y., & Bonoma, B. (2017). Modeling and simulation of an industrial indirect solar dryer for iroko wood (Chlorophora excelsa) in a tropical environment. Maderas: Ciencia y Tecnologia, 19(1), 95–112.




DOI: https://doi.org/10.31315/e.v20i1.8166

Refbacks

  • There are currently no refbacks.

Article Metrics

Metrics Loading ...

Metrics powered by PLOS ALM


Eksergi p-ISSN  1410-394X, e-ISSN 2460-8203,  is published by "Prodi Teknik Kimia UPN Veteran Yogyakarta".

Contact  Jl. SWK 104 (Lingkar Utara) Condong catur Sleman Yogyakarta

 

 Creative Commons License

Eksergi by http://jurnal.upnyk.ac.id/index.php/eksergi/index/ is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

 

 

Lihat Statistik Jurnal Kami

slot gacor slot gacor hari ini slot gacor 2025 demo slot pg slot gacor slot gacor